and if i'm not mistaken, gorillas are protected

and last but not least, starfish are endangered!

if this guy wasn't shot with a hamr, he should have been!

No Sir.
No Zebra l. Those are next door.

Straight up song dog I swear

And that Sir is what was said sniping this one.

What’s the hold for 125gr CC at 420yds?

And that Sir is what was said sniping this one.

What’s the hold for 125gr CC at 420yds?

[/quote]




fine shootin!!

if that was 420 yards, your zero musta been 400. but no matter, mine was 465 yards anyway.

I'm glad I've got my boots on, it's sure getting deep !!!

Are the 125 CC bullets still on track to release this week?

Honest injun. I swear.

Top of head hold base of neck impact

That yellow line is to the water tower in the video and it’s 900+

I just need the 125s to chrono and figure my table

They are somewhere between SD and AR on a semi-truck now, we'll package and get them on the website as soon as we get them in.

Will there be updated load data for the new CC 125 on the web site also?

Thank you very much for the update! Myself and I'm certain many others greatly appreciate your knowledgeable additions to and continued high level of interaction within this thread.

We should have it up by the time bullets are ready to ship, but here's the basic data.

Recommended loads that are all in the 2400-2420fps range where this bullet seems to shoot the best, MAX is a little above this, but this bullet doesn't shoot as well at MAX and we don't recommend exceeding 2450fps from a 16" barrel. This bullet will perform as designed down to an impact velocity of 1500fps so there is no reason to hot rod it.

26.5gr SW Blackout
25.5gr A1680
25.7gr CFEBLK
NOTE: POWDER LOTS WILL VARY

COL 2.250" with a medium crimp

thank you very much.....

third generation shooting supply has CFEBLK in stock for you fellas who are looking.

Mr Wilson or anyone familiar with WC factory built 300HAMR uppers: are the compensators/breaks rockset on the 16” uppers as they ship or is there a different thread locker used?

I’ve got a hunter enroute that is struggling with twisting off his Wilson comp to replace it with a Griffin taper mount muzzle device.

Thanks

We just install with a crush washer, Q-Comp usually isn't hard to remove, but sometimes the crush washer egg shapes some and has to be cut off. No sealant of any type is used.

Thank you very much.I passed the info along. I told him to not sweat it and not to force it if he wasn't comfortable. He can use one of my 16" HAMR's and we will look at it here.


So, about those 125gr CC?

ROFL

these posts came across while I was doing 80mph escaping to the Republic from the North Tundra & I didn't get what you were talking about.
Now I've seen them on a full screen I've been laughing like a drunk loon for 5 minutes.

Off to test more 110gr Vmax HAM'R

I have read through this whole thread, I think I want one! Is there any chance one of those THF discounts may be available?

Or just buy a few parts every month. Started in November and Finished Friday. Initial shooting today.

This is how I do my builds. Just about to start a .308 AR10 build. Between it and my two .300 Ham'rs all my needs will be covered. Might take a year to get all of the parts together but it's an enjoyable process.

Ok DJones. I’ve got my merit badge and am ready for the peanut fields call me up to the majors boss.

Does the 130 HHC have the same BC as the standard 130HC (.248)?
Reverse engineering the data on page 52 seems to suggest that, but measuring the bullets shows they are ~0.030" longer which should result in slightly better BC.
Am I crazy?