Special buy offer on all 300 HAM'R barrels and associated product to install at a 25% discount off regular web site prices

Offer ends at 4pm June 11

Contact Tressa Joubert via email (tressa@wilsoncombat.com) or by PH 800-955-4856, ext 104 to place your order

Now that's an offer that would be hard to beat.

I am in on this deal, the slick side has just been reallocated and the two builds pushed to the back burner

What's the difference? Threaded?

300 HAM'R, Tactical Hunter, 18", 1-15 Twist, Stainless, Fluted

300 HAM'R, Ultralight Hunter, 18", 1-15 Twist, Stainless, Fluted

Make sure you get the gas tube with it, in some cases you will need the WC gas tube to be the correct size

When you say "associated products to install" what does that mean? As in gas block, gas tube, and rail? But if I get that then I need a WC billet upper with 300 HAM'R engraved on the side. But if I get the upper I'll need a matching lower to go along with it. I got a cart going on the site right now and I'm up to $1300 to build the 8" pistol (SBR Later) before brace, grip, and trigger LOL.

Whatever you want that's a WC produced product including a complete rifle. Discount doesn't apply to non WC product such as dies, cases, etc... Most of this product will have a NW prefix part #. Tressa can help you with this and/or answer any ?s

You know , part of what makes THF one of the best forums on the net is the fact that the Moderators let discussions occur without interjecting or playing referee.

Also they don’t over react when a non paying Sponsor or Company makes an offer as you have. I’ve been on some forums when similar good intentioned offers/discounts are made and people freak out ... sad when it happens.

So hats off to the Mods and Mr. Wilson for what you do !

P.S. - don’t hold it against DJones when he decides to respond to my previous comment, I’m sure I elevated myself to his Special Project list...

Okay, couple of questions before I order, the Ultralight Hunter 18" without the threads has a .062" gas port list in the drawing and the Tactical Hunter 18" with threads has a .099" gas port, which is the correct gas port size?

I am wanting the Tactical Hunter

That is awesome right there. Double checking my order because my cart timed out. Trying to decide between 8" or 11.3". I do want to test the 8" side by side with the 300BLK, but if they're anywhere close to each other performance wise I'll essentially have 2 300BLK rifles.

I've never shot a 8", but they might be somewhat close due to the fact most BLK ammo is loaded with powders in the W296/H110 burn rate range and the CFEBLK we load the HAM'R with is much slower, thus not ideal for short bbls. However I've been testing some loads with Shooters World SBR SOCOM which is about half way between H110 and CFEBLK in burn rate with good initial success with light bullets. I'd expect it to give better velocity in the short bbls with most bullet weights. I never could get the guns to run with H110 due to the longer gas systems we use that dramatically reduce the bolt thrust and stress on the bolt. All that said the 8" has a pistol gas, so should work with H110.

For some reason some of the bbl spec on the web site has our initial testing port size, not the eventual port size we establish. .099" is the correct size on all 18" and 20" bbls with intermediate gas. Tks for bringing this to my attention, a fix is in process.

you're safe for the moment. i'm currently under thf psychiatric evaluation. i hope the result is a warning or at most the wall. my mom should have sought counseling for me at an early age when the principal told her... he just doesn't play well with others.

Well together we will get through this - GFY

Thanks Bill, think I'm going to go with the 8" barrel and load the 110VMAX with the H110. Same load as my Blackout only thing will be different is the extra case capacity. Will be an apples to apples comparison.

Same barrel length, same shooter, same trigger, same scope and mount, same primer, powder, and bullet. Only difference will be the brass.

If there is a problem...I'm going to lean toward that being it

Exactly the groups will be equally as bad LMAO

Ouch, this going to be an expensive test LOL. Even after the 25% off it'll be a tad over $1300 just to finish the gun, not including brass and dies.

LOL. I wouldn't do it. All these gap AR rounds are about the same anyway. You can't change the laws of physics.

LRoyal may not see a big difference when comparing the BLK to the HAM'R in a 8", but we've proven over and over there is a huge difference if 16" or longer barrels. Often 400fps+

Took this bad boy last night from 65yds, 150gr Hornady SST, DRT. The rifle is 42" long from butt to muzzle of suppressor. Actual weight on a scale 258# and he's a fat boar, not a bar. He's been raiding one of our deer protein feeders, but finally made a mistake!

What a beast he was...congrats Bill and thanks for offering the discount on the Hamr stuff.

Good looking rifle and optic !

Did that bullet pass through