Forums46
Topics538,056
Posts9,732,508
Members87,055
|
Most Online25,604 Feb 12th, 2024
|
|
|
Stub legs for feeder
#107143
11/08/06 01:55 PM
|
Joined: Nov 2006
Posts: 41
ovalohunter
OP
Light Foot
|
OP
Light Foot
Joined: Nov 2006
Posts: 41 |
Morning guys, and any ladies. I'm trying to build a 55 gal. feeder, and I'm doing tripod legs. I was going to buy the stub legs from Academy but the were only rated for a 30 gal. barrel. I have some sq. tubing, but didn't know what angle to bend or most likely cut and weld. Anyone know what I'm after or done this? Any advice? Thanks
|
|
|
Re: Stub legs for feeder
[Re: ovalohunter]
#107144
11/08/06 02:03 PM
|
Joined: Aug 2005
Posts: 17,117
MikeC
THF Celebrity
|
THF Celebrity
Joined: Aug 2005
Posts: 17,117 |
I usually cut and weld mine at 20 deg. Seems about right and I've never had one blow over or spread the legs. I usually use 2" square tube for legs and that helps too. If you are hunting where there are hogs or cattle it's impossible to build them too sturdy MC
|
|
|
Re: Stub legs for feeder
[Re: MikeC]
#107145
11/08/06 02:08 PM
|
Joined: Oct 2004
Posts: 37,484
Big Orn
great white gorilla
|
great white gorilla
Joined: Oct 2004
Posts: 37,484 |
Mike is right about building it sturdy!!
I would go anywhere from 20 to 30 degrees - from vertical - depending on the terrain. 20 would be fine on good level ground, up to 30 on slight hills and such.
|
|
|
Re: Stub legs for feeder
[Re: ovalohunter]
#107146
11/08/06 02:22 PM
|
Joined: May 2006
Posts: 2,144
jbhlsu
Veteran Tracker
|
Veteran Tracker
Joined: May 2006
Posts: 2,144 |
Hang it!! Rig a spreader bar on it...drill two holes in the barrel attach spreader bar..Go to Northern tool supply or were ever...buy smoe cable and cheap 1000 cap. winch...Upper pulley in tree and cut off 10" thick cedar 2ft off ground...attach winch..you good to go...JMO..Dont use the ones from academy..they are weak!! good luck hunting to all!
|
|
|
Re: Stub legs for feeder
[Re: jbhlsu]
#107147
11/08/06 03:19 PM
|
Joined: Aug 2004
Posts: 17,721
Txduckman
THF Celebrity
|
THF Celebrity
Joined: Aug 2004
Posts: 17,721 |
Wire t-posts to each leg and it should not have any reason to fall over.
|
|
|
Re: Stub legs for feeder
[Re: Txduckman]
#107148
11/09/06 01:19 PM
|
Joined: Nov 2006
Posts: 41
ovalohunter
OP
Light Foot
|
OP
Light Foot
Joined: Nov 2006
Posts: 41 |
Thanks guys, I'm gonna make the stubs 20 deg. I am going to use t-posts as anchors. Should have corn in it Friday afternoon. Thanks alot!
|
|
|
Re: Stub legs for feeder
[Re: ovalohunter]
#107149
11/11/06 02:34 AM
|
Joined: Oct 2006
Posts: 6
pn_fireman
Green Horn
|
Green Horn
Joined: Oct 2006
Posts: 6 |
All I did was bought the leg kit from BassPro (it extend from the barrell about 12" if i remember right). Then got 3 sections of top rail (for chain link fence). Worked like a charm. I did cut holes in it with a cutting torch so i could stake a short piece of rebar through it into the ground. Even the E. Texas hogs couldn't knock it over.
|
|
|
Re: Stub legs for feeder
[Re: Txduckman]
#107150
11/12/06 06:21 PM
|
Joined: Jul 2006
Posts: 589
Grinder
Tracker
|
Tracker
Joined: Jul 2006
Posts: 589 |
Quote:
Wire t-posts to each leg and it should not have any reason to fall over.
I've T-posted mine and the hogs still work them over. I've found that using heavy T-post along with 2" steel heavy gage 10' fence posts works best when there are hogs and cattle around. Also, having the barrel so high that the cows can't head butt the timer helps alot. I've had the most sucess with the spin-caster brand feeder timers. They don't leak corn out when the cows or hogs rub on the post or pipe.
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, TreeBass, txcornhusker
|