texashuntingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
TraeMartin, Beatixre, MooseSteed, Trappernewt, casyoo
71987 Registered Users
Top Posters(All Time)
dogcatcher 110,788
bill oxner 91,416
SnakeWrangler 65,416
stxranchman 60,296
Gravytrain 46,950
RKHarm24 44,585
rifleman 44,461
Stub 43,769
Forum Statistics
Forums46
Topics537,022
Posts9,719,496
Members86,987
Most Online25,604
Feb 12th, 2024
Print Thread
Camber Bolts for level kit? #7593079 08/29/19 06:47 PM
Joined: Jul 2014
Posts: 6,279
onlysmith&wesson Online Content OP
THF Trophy Hunter
OP Online Content
THF Trophy Hunter
Joined: Jul 2014
Posts: 6,279
I don't know anything about this modification. I've had 4WD vehicles all my life but ran them stock. The worst they see is sticky mud at the lease here in north Texas.
I have a new F150 with the FX4 package, 20" wheels. I'm not wanting anything aggressive, just raise the front end to give it a more level look without putting a strain on front end parts or wreck the great gas mileage I'm getting. This twin turbo ECO Boost runs great.
A dealer ship is wanting to sell me a level kit installed with an alignment for about $850.00. They tell me they go the extra mile and install camber bolts that allow for a better adjustment on camber. A local shop with a good reputation tells me I don't need them and will do a level kit install with alignment for $450.00. Both prices are for a 2" level. I've had the truck 6 months and am really happy with the ride and mileage. What do ya'll say?


An unethical shot is one you take, that you know you shouldn't.
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7593423 08/30/19 12:39 AM
Joined: Feb 2009
Posts: 151
T
TORNracer Offline
Woodsman
Offline
Woodsman
T
Joined: Feb 2009
Posts: 151
I have no input, but have been wanting to do the same thing with my 2019 Platinum EcoBoost. Love the truck just wish the front was 1.5-2 inches taller. Would love to see everyone’s thoughts on this!

Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7593504 08/30/19 01:48 AM
Joined: Feb 2010
Posts: 7,243
J
jhenderson Online Content
THF Trophy Hunter
Online Content
THF Trophy Hunter
J
Joined: Feb 2010
Posts: 7,243
Price sounds extremely high at the dealer. If it can be aligned to spec I don’t see a reason to do the bolts personally.

Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7593697 08/30/19 12:00 PM
Joined: Mar 2007
Posts: 5,225
R
Rustler Offline
THF Trophy Hunter
Offline
THF Trophy Hunter
R
Joined: Mar 2007
Posts: 5,225
I'm with jhenderson, if it aligns to spec no reason.

I've installed a bunch of them, never had one need camber adjustment, usually use 1.5" 'kit'.

This is what I would use, they have from 1.5" ~ 2.5" kits.
---> Autospring 1.5"

Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7593774 08/30/19 01:16 PM
Joined: Jul 2014
Posts: 6,279
onlysmith&wesson Online Content OP
THF Trophy Hunter
OP Online Content
THF Trophy Hunter
Joined: Jul 2014
Posts: 6,279
That's good to know, I appreciate the feedback. Rustler, can you recommend the shop you used, and you have any before/after pic's of the 1-1/2" level? I'd like to not go over 2", if I could get the results I'm after with the 1-1/2" I'd do it. Thanks.


An unethical shot is one you take, that you know you shouldn't.
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7594718 08/31/19 04:54 PM
Joined: Feb 2010
Posts: 7,243
J
jhenderson Online Content
THF Trophy Hunter
Online Content
THF Trophy Hunter
J
Joined: Feb 2010
Posts: 7,243
I’ve used north Texas truck accessories on 121 business fair honest and good pricing.

Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7594749 08/31/19 05:52 PM
Joined: Mar 2007
Posts: 5,225
R
Rustler Offline
THF Trophy Hunter
Offline
THF Trophy Hunter
R
Joined: Mar 2007
Posts: 5,225
Originally Posted by onlysmith&wesson
That's good to know, I appreciate the feedback. Rustler, can you recommend the shop you used, and you have any before/after pic's of the 1-1/2" level? I'd like to not go over 2", if I could get the results I'm after with the 1-1/2" I'd do it. Thanks.


I don't have any pictures, did 99% for freinds realitives & acquaintances.
Never paid a shop to install, simple bolt off bolt on installation. With hand tools jacks & jack stands easy to do with basic mechanical aptitude.
Then to the dealer, tire shop / anywhere trustable for an alignment check & toe in/out adjustment.

If you go with the source I linked to they usually give slightly more 'lift' than stated, slightly.

On a flat surface measure from ground through center line of wheel to edge of fender lip/edge front & rear.
Notate the difference, pick the kit that will give the look you're after.
To me they look best with the rear still at least an inch higher.

For me a level pickup is useless, put a couple hundred lbs in the bed or hook up a trailer you end up nose high.

AS used to have before & after pictures on their site, give them a call, always been friendly helpful folks.



Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7620093 09/30/19 05:45 PM
Joined: Jul 2005
Posts: 3,304
S
Stump_jumper Offline
Veteran Tracker
Offline
Veteran Tracker
S
Joined: Jul 2005
Posts: 3,304
Keep it below 3" and should not have any special needs parts wise to get a proper alignment. If you spend any time off road the I would skip the spacer blocks and go with an adjustable coil over. Those spacers can stress the shocks. I went with Bilstein 6112s preassembled. I installed myself for $750 + $80 alignment. The dealer's price is way too high for what you are getting. My toe was just slightly off. I little less expense that the 6112s is to go with a 5100.


2017 Tundra 5.7 CM 4x4
2006 Champion 2200 Bay Boat
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7620359 09/30/19 11:10 PM
Joined: Jul 2014
Posts: 6,279
onlysmith&wesson Online Content OP
THF Trophy Hunter
OP Online Content
THF Trophy Hunter
Joined: Jul 2014
Posts: 6,279
I went with Bilsteins height adjustable struts. Great ride, perfect look that I wanted. Had the shop set them at the max of 2" to the front, no modification to the back. [Linked Image]

Last edited by onlysmith&wesson; 09/30/19 11:11 PM. Reason: added pic's

An unethical shot is one you take, that you know you shouldn't.
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7620603 10/01/19 04:26 AM
Joined: Feb 2009
Posts: 151
T
TORNracer Offline
Woodsman
Offline
Woodsman
T
Joined: Feb 2009
Posts: 151
That looks awesome. Are you perfectly level or do you still have a little rake? I was looking at those same Bilsteins for mine....

Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7620633 10/01/19 10:35 AM
Joined: Jul 2014
Posts: 6,279
onlysmith&wesson Online Content OP
THF Trophy Hunter
OP Online Content
THF Trophy Hunter
Joined: Jul 2014
Posts: 6,279
Really so close I can't tell. Very happy with the ride.


An unethical shot is one you take, that you know you shouldn't.
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7620634 10/01/19 10:36 AM
Joined: Jul 2014
Posts: 6,279
onlysmith&wesson Online Content OP
THF Trophy Hunter
OP Online Content
THF Trophy Hunter
Joined: Jul 2014
Posts: 6,279
Epic 4 x 4, $600.00 OTD. 121 in Lewisville.


An unethical shot is one you take, that you know you shouldn't.
Re: Camber Bolts for level kit? [Re: onlysmith&wesson] #7621024 10/01/19 05:44 PM
Joined: Jul 2005
Posts: 3,304
S
Stump_jumper Offline
Veteran Tracker
Offline
Veteran Tracker
S
Joined: Jul 2005
Posts: 3,304
Originally Posted by onlysmith&wesson
I went with Bilsteins height adjustable struts. Great ride, perfect look that I wanted. Had the shop set them at the max of 2" to the front, no modification to the back. [Linked Image]

only 2 problems here #1 it is a Ford and #2 it is black. Like I said in a previous post I put the 6112s on mine. I replaced the whole assembly and sold the OEMs. [Linked Image]


2017 Tundra 5.7 CM 4x4
2006 Champion 2200 Bay Boat
Previous Thread
Index
Next Thread

© 2004-2024 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3