Forums46
Topics537,952
Posts9,731,011
Members87,051
|
Most Online25,604 Feb 12th, 2024
|
|
|
Vortex and Leupold ring screw tension
#7044828
01/19/18 06:45 PM
|
Joined: Jul 2012
Posts: 15,699
603Country
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Jul 2012
Posts: 15,699 |
Ok, got my Fatmax torque wrench and am about to get to torquing various screws to their recommended tension. Vortex recommends 18 in/lbs for their ring screws and Leupold recommends 15 - 17 in/lbs. I have a question for you serious shooters, and you know who you are. Do you fellows torque to the recommendation, or do you vary for any reason? If you do vary, what is your reasoning?
Thanks
Not my monkeys, not my circus...
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7045221
01/19/18 11:06 PM
|
Joined: Dec 2008
Posts: 41,171
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,171 |
1" tube 20 in/lbs
30mm tube 25 in/lbs
34mm tube 25 in/lbs
Works, never caused any trouble.
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7045230
01/19/18 11:10 PM
|
Joined: Mar 2012
Posts: 3,809
Cleric
Extreme Tracker
|
Extreme Tracker
Joined: Mar 2012
Posts: 3,809 |
i follow mfg recommendations...
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7045373
01/20/18 12:57 AM
|
Joined: Dec 2008
Posts: 41,171
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,171 |
^^And that's good if they are available.
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7045456
01/20/18 01:39 AM
|
Joined: Jul 2012
Posts: 15,699
603Country
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Jul 2012
Posts: 15,699 |
Gotta say...I like the FatWrench. Worked great. I went with about 18 in/lbs, though I can see the joy in using 20 pounds, since that’s a clear mark. The process gave me a chance to adjust the reticle that had been a teeny bit canted.
Decided to just leave the Leupold VariX-III 4.5-14 on the 223. The repaired Vortex will sit on the shelf, I suppose.
Not my monkeys, not my circus...
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7045531
01/20/18 02:40 AM
|
Joined: Jan 2011
Posts: 2,394
booradley
Veteran Tracker
|
Veteran Tracker
Joined: Jan 2011
Posts: 2,394 |
What the manufacturer says.
Don’t roll those bloodshot eyes at me.
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7047803
01/22/18 02:01 AM
|
Joined: Mar 2015
Posts: 1,038
TXBoss
Pro Tracker
|
Pro Tracker
Joined: Mar 2015
Posts: 1,038 |
Not speaking as an expert shooter... but here's my perspective as one who works with fasteners.
The torque recommendation if available by the mfg should be followed as it "should" be based on the fastener (size, thread pitch and materials). If the rings are manufactured correctly - geometry, the threads are by far the weakest link.
You want just enough torque to keep the fastener in tension. Too much and you will yield the material or worse, strip the female thread.
Keep in mind any manufacturer recommendation for using a thread locking compound as well as it could change the friction properties of the fastener.
"Good judgment comes from experience, and a lot of that comes from bad judgment..." - W. Rogers
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: 603Country]
#7047867
01/22/18 02:42 AM
|
Joined: Dec 2008
Posts: 41,171
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,171 |
Are a few inch pounds over manufacturer recommendation the end of the world?
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: Vortex and Leupold ring screw tension
[Re: J.G.]
#7048014
01/22/18 04:59 AM
|
Joined: Mar 2015
Posts: 1,038
TXBoss
Pro Tracker
|
Pro Tracker
Joined: Mar 2015
Posts: 1,038 |
Are a few inch pounds over manufacturer recommendation the end of the world? It depends... but you don't ever want to find out as once a fastener gets over-torqued it will never be able to retain the tension you need. Again... perfect world... and most of what I'm talking about is really applicable for a much larger fastener application. Just look at head bolts and gasket compression and the sensitivity to retained tension. And you're right.. its not a great amount... and all probably within the accuracy of some torque wrenches. But it is something to consider.
Last edited by TXBoss; 01/22/18 05:00 AM.
"Good judgment comes from experience, and a lot of that comes from bad judgment..." - W. Rogers
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, txcornhusker
|