Forums46
Topics537,784
Posts9,729,095
Members87,042
|
Most Online25,604 Feb 12th, 2024
|
|
|
different headspace measurements on fired brass
#6887323
09/14/17 05:54 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
I felt several chamberings that felt real snug on the .308 and fired all the loaded rounds. When I measured the headspace on the fired brass ( to bump .002" on the Redding body die ) and there was a variance of .003" I have not experienced that before and so I put the whole batch of brass through the body die and bumped back .002" and neck sized for the next loading. What would be the issue of the .001" - .003" variance between fired brass?
Last edited by TackDriver; 09/14/17 05:56 PM.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887334
09/14/17 06:00 PM
|
Joined: Sep 2009
Posts: 18,935
ChadTRG42
THF Celebrity
|
THF Celebrity
Joined: Sep 2009
Posts: 18,935 |
Is it all the same head stamp (same brand and lot)? It could be a small variation from piece to piece. It could also be a slight variation on the case head. I've had some pieces of brass that had the rim ever so slightly bent, and would throw off a head space measurement by a few thousandths.
I've seen .001"-.002" variation. I size to the shortest one. I'm not worried about 1 or 2 thou, though. Size it to the shortest piece you are measuring, and call it good. Just chamber check your brass after sizing to make sure it chambers smooth.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887355
09/14/17 06:24 PM
|
Joined: Nov 2011
Posts: 4,563
patriot07
Extreme Tracker
|
Extreme Tracker
Joined: Nov 2011
Posts: 4,563 |
I'm new to the reloading game, but I will say that from an engineering standpoint, .001" is just absolutely nothing. It's hard to control anything to that level. Some of this reloading equipment is really capable of top-notch precision, but it's very difficult to understand how small that type of distance really is. I'm amazed that you guys can control this stuff as well as you do.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887378
09/14/17 06:52 PM
|
Joined: Sep 2009
Posts: 18,935
ChadTRG42
THF Celebrity
|
THF Celebrity
Joined: Sep 2009
Posts: 18,935 |
If you think about, the typical max to min headspace on a go, no-go gauge is .006" (sometimes .007"). A few thousands difference in the head space area is VERY important.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887400
09/14/17 07:22 PM
|
Joined: Nov 2011
Posts: 4,563
patriot07
Extreme Tracker
|
Extreme Tracker
Joined: Nov 2011
Posts: 4,563 |
I believe it. It's just very impressive to me that they've created affordable tools that can control dimensions to that type of precision.
|
|
|
Re: different headspace measurements on fired brass
[Re: ChadTRG42]
#6887465
09/14/17 08:22 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
Is it all the same head stamp (same brand and lot)? It could be a small variation from piece to piece. It could also be a slight variation on the case head. I've had some pieces of brass that had the rim ever so slightly bent, and would throw off a head space measurement by a few thousandths.
I've seen .001"-.002" variation. I size to the shortest one. I'm not worried about 1 or 2 thou, though. Size it to the shortest piece you are measuring, and call it good. Just chamber check your brass after sizing to make sure it chambers smooth. Yes Chad, its all the same headstamp, its Lapua brass, all the same lot, fired the same number of times. Fired 6 X's. Most are .001 to .002 off, a few are .003"
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887550
09/14/17 09:15 PM
|
Joined: Sep 2009
Posts: 18,935
ChadTRG42
THF Celebrity
|
THF Celebrity
Joined: Sep 2009
Posts: 18,935 |
Well, after so many firings, you can get some brass flow in various areas. I'd call it good if it was within .002", honestly.
|
|
|
Re: different headspace measurements on fired brass
[Re: patriot07]
#6887980
09/15/17 03:53 AM
|
Joined: May 2016
Posts: 352
cblackall
Bird Dog
|
Bird Dog
Joined: May 2016
Posts: 352 |
I'm new to the reloading game, but I will say that from an engineering standpoint, .001" is just absolutely nothing. It's hard to control anything to that level. Some of this reloading equipment is really capable of top-notch precision, but it's very difficult to understand how small that type of distance really is. I'm amazed that you guys can control this stuff as well as you do. I understand where you're coming from. I've been reloading for nearly 20 years, and 10-20 thousandths of an inch doesn't sound or look like much of anything. But when you're dealing with firearms and ammunition, it might as well be miles. It's amazing how much difference a couple thousandths will make, be it a round chambering or not or the difference in safe or unsafe.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887987
09/15/17 04:02 AM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6887997
09/15/17 04:16 AM
|
Joined: May 2017
Posts: 5,189
Smokey Bear
THF Trophy Hunter
|
THF Trophy Hunter
Joined: May 2017
Posts: 5,189 |
TD, have you annealed? That would be by first thought. After several firings the malleability of the brass will not be as consistent and you can get differences in spring back after sizing. One other thing to check if your are loading up near max, particularly if you have been shooting in hot weather. A slight ejector swipe can give you inconsistent measurements depending if your caliper is on the mark or not. A few thousands isn't much but examining the case head through a magnifying glass will allow you to see it.
Smokey Bear---Lone Star State.
|
|
|
Re: different headspace measurements on fired brass
[Re: Smokey Bear]
#6888125
09/15/17 12:56 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
TD, have you annealed? That would be by first thought. After several firings the malleability of the brass will not be as consistent and you can get differences in spring back after sizing. One other thing to check if your are loading up near max, particularly if you have been shooting in hot weather. A slight ejector swipe can give you inconsistent measurements depending if your caliper is on the mark or not. A few thousands isn't much but examining the case head through a magnifying glass will allow you to see it. Yes, I annealed prior to firing them and they were under max load with 44.4 grains of Varget at 2,770 fps with no pressure signs at all, no ejector swipe. The weather was cooler this time out at 75 degrees compared to 90 prior to that. Even did all case prep prior to firing. That bugs me.
Last edited by TackDriver; 09/15/17 12:57 PM.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6888195
09/15/17 01:59 PM
|
Joined: Dec 2008
Posts: 41,160
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,160 |
Were you measuring head space on a fired primer, or after decapping?
If with a fired primer in the pocket, and if there is any flow back, on the primer, around the firing pin strike it will throw off your head space measurement.
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6888216
09/15/17 02:21 PM
|
Joined: Nov 2007
Posts: 9,517
RiverRider
THF Trophy Hunter
|
THF Trophy Hunter
Joined: Nov 2007
Posts: 9,517 |
One other idea...if this is new brass, it may not yet be fully fireformed to your chamber.
"Arguing with you always makes me thirsty." -Augustus McRae
|
|
|
Re: different headspace measurements on fired brass
[Re: J.G.]
#6888225
09/15/17 02:26 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
Were you measuring head space on a fired primer, or after decapping?
If with a fired primer in the pocket, and if there is any flow back, on the primer, around the firing pin strike it will throw off your head space measurement. I used the Lee decapper first and decapped all primers and measured after.
|
|
|
Re: different headspace measurements on fired brass
[Re: RiverRider]
#6888226
09/15/17 02:27 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
One other idea...if this is new brass, it may not yet be fully fireformed to your chamber. Brass is on 6th firing.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6888246
09/15/17 02:42 PM
|
Joined: Dec 2008
Posts: 41,160
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,160 |
How clean is your bolt face, and how clean is your chamber?
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: different headspace measurements on fired brass
[Re: J.G.]
#6888256
09/15/17 02:48 PM
|
Joined: Jun 2011
Posts: 33,946
Buzzsaw
THF Celebrity
|
THF Celebrity
Joined: Jun 2011
Posts: 33,946 |
How clean is your bolt face, and how clean is your chamber? sounds weird but this is a good idea when you are talking thousands of an inch.
|
|
|
Re: different headspace measurements on fired brass
[Re: J.G.]
#6888385
09/15/17 04:30 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
How clean is your bolt face, and how clean is your chamber? Boltface was clean, barrel was cleaned and not sure about the chamber being clean, I'll take a look at it. I'll run a mop thru the chamber next time out.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6888436
09/15/17 05:08 PM
|
Joined: Sep 2006
Posts: 32,484
kmon11
junior
|
junior
Joined: Sep 2006
Posts: 32,484 |
Long shot reason but worth asking.
Clean all the case lube off the cases? Or were some more slick than others?
Depending on the rifle When the cases are sized say with a .002 shoulder bump, when the firing pin hits it can drive the case forward that amount or a little more since brass is springy there might be another thousandth or so in the head space. Ignition starts and pressures build. With a slick case it gets pushed back harder against the bolt face and can stretch a little more than a case that grips the chamber tightly.
lf the saying "Liar, Liar your pants on fire" were true Mainstream news might be fun to watch
|
|
|
Re: different headspace measurements on fired brass
[Re: kmon11]
#6888708
09/15/17 10:21 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
Long shot reason but worth asking.
Clean all the case lube off the cases? Or were some more slick than others?
Depending on the rifle When the cases are sized say with a .002 shoulder bump, when the firing pin hits it can drive the case forward that amount or a little more since brass is springy there might be another thousandth or so in the head space. Ignition starts and pressures build. With a slick case it gets pushed back harder against the bolt face and can stretch a little more than a case that grips the chamber tightly. Cleaned necks prior to loading as well.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6888800
09/16/17 12:49 AM
|
Joined: May 2017
Posts: 5,189
Smokey Bear
THF Trophy Hunter
|
THF Trophy Hunter
Joined: May 2017
Posts: 5,189 |
Reading your posts it sounds like you are pretty thorough. If you are using a comparator with headspace bushing on your caliper, there may have been a little slack when you tightened things down. .003 is not much slack. Good luck working it out. It would gnaw on me till I figured it out too. In the end better consistency and chambering is why a lot of reloaders seeking precision, go with a partial full length size with a minimal shoulder bump every cycle. That is an old debate among loaders with pros and cons to both methods that I am not trying to get started.
Smokey Bear---Lone Star State.
|
|
|
Re: different headspace measurements on fired brass
[Re: Smokey Bear]
#6888816
09/16/17 01:18 AM
|
Joined: Nov 2007
Posts: 9,517
RiverRider
THF Trophy Hunter
|
THF Trophy Hunter
Joined: Nov 2007
Posts: 9,517 |
That is an old debate among loaders with pros and cons to both methods that I am not trying to get started. It's seven weeks until deer season. We got time.
"Arguing with you always makes me thirsty." -Augustus McRae
|
|
|
Re: different headspace measurements on fired brass
[Re: RiverRider]
#6888838
09/16/17 01:37 AM
|
Joined: May 2017
Posts: 5,189
Smokey Bear
THF Trophy Hunter
|
THF Trophy Hunter
Joined: May 2017
Posts: 5,189 |
LOL. I'm an old guy that's walked both paths.
Smokey Bear---Lone Star State.
|
|
|
Re: different headspace measurements on fired brass
[Re: TackDriver]
#6889003
09/16/17 11:58 AM
|
Joined: Dec 2008
Posts: 41,160
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,160 |
How clean is your bolt face, and how clean is your chamber? Boltface was clean, barrel was cleaned and not sure about the chamber being clean, I'll take a look at it. I'll run a mop thru the chamber next time out. What caliper do you have? Are you 100% sure the instrument is accurate?
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: different headspace measurements on fired brass
[Re: J.G.]
#6889022
09/16/17 12:34 PM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
How clean is your bolt face, and how clean is your chamber? Boltface was clean, barrel was cleaned and not sure about the chamber being clean, I'll take a look at it. I'll run a mop thru the chamber next time out. What caliper do you have? Are you 100% sure the instrument is accurate? Yes Fireman, I tested it several times and right to the point. RCBS digital.
Last edited by TackDriver; 09/16/17 12:35 PM.
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, TreeBass, txcornhusker
|