texashuntingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
TraeMartin, Beatixre, MooseSteed, Trappernewt, casyoo
71987 Registered Users
Top Posters(All Time)
dogcatcher 110,788
bill oxner 91,416
SnakeWrangler 65,416
stxranchman 60,296
Gravytrain 46,950
RKHarm24 44,585
rifleman 44,461
Stub 43,769
Forum Statistics
Forums46
Topics537,021
Posts9,719,476
Members86,987
Most Online25,604
Feb 12th, 2024
Print Thread
Cleaning between firings #7042882 01/18/18 01:40 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
I got a little tired of hijacking the other thread.

How do you guys clean between firings, if you're trying to load for max accuracy? I have been cleaning with a vibratory tumbler that my buddy at work let me borrow. It has corn cob media I think, with polish added. They come out looking great, but they do have a fine film on them, inside & out.

Re: Cleaning between firings [Re: patriot07] #7042892 01/18/18 01:46 PM
Joined: Apr 2010
Posts: 6,219
D
dee Offline
THF Trophy Hunter
Offline
THF Trophy Hunter
D
Joined: Apr 2010
Posts: 6,219
Ultrasonic.

I've used vibratory but with walnut media. It worked too but takes longer.


"A vote is like a rifle; it's usefulness depends on the character of the user" Theodore Roosevelt
Re: Cleaning between firings [Re: patriot07] #7042898 01/18/18 01:51 PM
Joined: Mar 2009
Posts: 4,422
J
jeffbird Offline
Extreme Tracker
Offline
Extreme Tracker
J
Joined: Mar 2009
Posts: 4,422
Tumbler with plain corn cob, nothing added, before sizing to protect the sizing die and again after sizing to remove all sizing lube. I turn it on before going to sleep and turn it off in the morning. New brass is cleaned only after going through the sizer to straighten dented necks, and does not take long.

Hornady One Shot is used for lube, except for setting up a new die. Then Imperial Sizing lube is used to avoid sticking a case.


Re: Cleaning between firings [Re: patriot07] #7042912 01/18/18 02:04 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
Do you wipe the film off of the outside of the case or out of the inside of the neck after cleaning?

Last edited by patriot07; 01/18/18 02:05 PM.
Re: Cleaning between firings [Re: patriot07] #7042919 01/18/18 02:11 PM
Joined: Mar 2009
Posts: 4,422
J
jeffbird Offline
Extreme Tracker
Offline
Extreme Tracker
J
Joined: Mar 2009
Posts: 4,422
Just toss them in the tumbler and it cleans them up overnight.

Re: Cleaning between firings [Re: patriot07] #7042929 01/18/18 02:19 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
I was specifically talking about the film from the cleaning media.

Re: Cleaning between firings [Re: jeffbird] #7042930 01/18/18 02:19 PM
Joined: May 2014
Posts: 1,100
T
TackDriver Offline
Pro Tracker
Offline
Pro Tracker
T
Joined: May 2014
Posts: 1,100
Originally Posted By: jeffbird
Just toss them in the tumbler and it cleans them up overnight.


There is dust on the cases after tumbling, is that normal?

Re: Cleaning between firings [Re: patriot07] #7042932 01/18/18 02:21 PM
Joined: Oct 2012
Posts: 29,576
S
Sneaky Online Content
THF Celebrity
Online Content
THF Celebrity
S
Joined: Oct 2012
Posts: 29,576
A film of what? Tumbling media dust?

Re: Cleaning between firings [Re: patriot07] #7042939 01/18/18 02:23 PM
Joined: Sep 2009
Posts: 18,907
C
ChadTRG42 Online Happy
THF Celebrity
Online Happy
THF Celebrity
C
Joined: Sep 2009
Posts: 18,907
Fired brass I tumble clean in corn cob media treated with Graf's brass case polish (best I have found) and pour a little in each use. If there's any dust, I'll wipe them down with a towel, then add some water to my media to cut the dust down. Size brass case, tumble again in media to get lube off. Load, go shoot, and repeat.

If I am only sizing a few cases (which is rare), I'll wipe them down, but I hate manually wiping them with a towel.


[Linked Image]
Custom and Precision Ammunition!!
https://DallasReloads.com/
Type 01 and Type 06 FFL
Re: Cleaning between firings [Re: Sneaky] #7042959 01/18/18 02:31 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
Originally Posted By: Sneaky
A film of what? Tumbling media dust?
Yes

So it sounds like nobody cares about the dust inside the neck? Seems like it might mess with neck tension like having lube in there would, but apparently not.

Re: Cleaning between firings [Re: patriot07] #7042968 01/18/18 02:35 PM
Joined: Jun 2011
Posts: 33,798
B
Buzzsaw Online Content
THF Celebrity
Online Content
THF Celebrity
B
Joined: Jun 2011
Posts: 33,798
important step, but again, don't overthink the process


SPACE FOR RENT


Re: Cleaning between firings [Re: ChadTRG42] #7042972 01/18/18 02:37 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
Originally Posted By: ChadTRG42
Fired brass I tumble clean in corn cob media treated with Graf's brass case polish (best I have found) and pour a little in each use. If there's any dust, I'll wipe them down with a towel, then add some water to my media to cut the dust down. Size brass case, tumble again in media to get lube off. Load, go shoot, and repeat.

If I am only sizing a few cases (which is rare), I'll wipe them down, but I hate manually wiping them with a towel.
up

Re: Cleaning between firings [Re: jeffbird] #7042975 01/18/18 02:38 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
Originally Posted By: jeffbird
Tumbler with plain corn cob, nothing added, before sizing to protect the sizing die and again after sizing to remove all sizing lube. I turn it on before going to sleep and turn it off in the morning. New brass is cleaned only after going through the sizer to straighten dented necks, and does not take long.

Hornady One Shot is used for lube, except for setting up a new die. Then Imperial Sizing lube is used to avoid sticking a case.

Thanks. Is there anything inherently wrong with RCBS lube? Lots of folks seem to be using the Hornady.

Re: Cleaning between firings [Re: patriot07] #7042986 01/18/18 02:42 PM
Joined: Sep 2009
Posts: 18,907
C
ChadTRG42 Online Happy
THF Celebrity
Online Happy
THF Celebrity
C
Joined: Sep 2009
Posts: 18,907
Brad, try to keep things simple when starting out reloading and only change one variable at a time. It sounds like it being over complicated where it's really a simple process.


[Linked Image]
Custom and Precision Ammunition!!
https://DallasReloads.com/
Type 01 and Type 06 FFL
Re: Cleaning between firings [Re: patriot07] #7042992 01/18/18 02:47 PM
Joined: Jan 2017
Posts: 290
S
snarkscarbine Offline
Bird Dog
Offline
Bird Dog
S
Joined: Jan 2017
Posts: 290
Cut up a dryer sheet or two into strips and toss it in to your media when tumbling. Also, a dollop of Final Finish car polish cuts down tumbling time by about half and leaves them SHINY. I'm trying short grain rice instead of walnut or corn cob. I've used it once thus far, and it seems to clean just as well, but without all of the moon dust afterward.

Re: Cleaning between firings [Re: snarkscarbine] #7042998 01/18/18 02:51 PM
Joined: Sep 2009
Posts: 18,907
C
ChadTRG42 Online Happy
THF Celebrity
Online Happy
THF Celebrity
C
Joined: Sep 2009
Posts: 18,907
Originally Posted By: snarkscarbine
Cut up a dryer sheet or two into strips and toss it in to your media when tumbling. Also, a dollop of Final Finish car polish cuts down tumbling time by about half and leaves them SHINY. I'm trying short grain rice instead of walnut or corn cob. I've used it once thus far, and it seems to clean just as well, but without all of the moon dust afterward.


Drier sheet- be careful, because I have had them separate and clog into the brass cases.

Final Finish- yes, it gets brass cases very clean, but it leaves a film on the brass, and can make it difficult during sizing. I used to use it, but switched to a true brass polish, which works much better.


[Linked Image]
Custom and Precision Ammunition!!
https://DallasReloads.com/
Type 01 and Type 06 FFL
Re: Cleaning between firings [Re: patriot07] #7043012 01/18/18 03:02 PM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
I'm going to try to put some water in next time to minimize the dust film.

I don't necessarily care about it being there if it doesn't impact accuracy. I'm just trying to figure out what variables to start adjusting to get my gun to group better with fired brass.

ETA: to be fair, the only variable I've changed so far is brass sizing method. I'm just trying to figure out where to go from there since the results were less than stellar. I've gotten good feedback on lube (could be the issue), cleaning (probably not the issue), and rifle condition (just need to leave it dirty). I'll see what I can do to eliminate some of those variables one at a time.

Last edited by patriot07; 01/18/18 03:06 PM.
Re: Cleaning between firings [Re: patriot07] #7043026 01/18/18 03:12 PM
Joined: Dec 2008
Posts: 41,083
J.G. Online Content
THF Celebrity
Online Content
THF Celebrity
Joined: Dec 2008
Posts: 41,083
All my brass but range pick-up goes in a Hornady vibratory with walnut shell that came with a polish already blended in. I got it from Cabela's.

I used to use corn cob. It seems to be softer, and dulls quicker. I've been happier with the walnut shell. All I really care about it clean, it is also making it shiny.


[Linked Image]
800 Yard Steel Range
Precision Rifle Instruction
Memberships and Classes Available
Re: Cleaning between firings [Re: patriot07] #7043061 01/18/18 03:38 PM
Joined: Mar 2009
Posts: 4,571
D
deewayne2003 Online Content
Extreme Tracker
Online Content
Extreme Tracker
D
Joined: Mar 2009
Posts: 4,571

I de-prime all my rifle cases with a universal de-priming die from Lee, then tumble in corncob media treated with Flitz polish and add a dryer sheet to collect dust.

Then I lubricate with Hornady case lube, full length size, trim to length and chamfer; followed by tumbling for a couple of hours in treated walnut media again with a dryer sheet.

My final step that a lot of people have denounced is taking my completed rounds and tumbling them in a separate batch of walnut media I have with just enough kerosene to barley wet the media - and I do mean just enough to barely wet the media, so were talking about 1.5-2oz in a tumbler full of media and only 10-15 minutes of tumbling.

An old timer told me about this and the thinking is that the walnut media dampened with Kerosene will remove any lube/residue off the cases and bullets as well as leaving a VERY light protective coating of Kerosene on the outside of the completed round..... They come out looking factory new and will store for years without tarnishing.

Some people freak out when I tell them I finish my loaded rifle ammo by tumbling in media with Kerosene but it has worked flawlessly for me for years.

Re: Cleaning between firings [Re: patriot07] #7043348 01/18/18 07:18 PM
Joined: Mar 2009
Posts: 4,422
J
jeffbird Offline
Extreme Tracker
Offline
Extreme Tracker
J
Joined: Mar 2009
Posts: 4,422
patriot,

Glen Zediker’s book on handloading is an outstanding resource, which is incredibly helpful.

A few equipment suggestions such as a Gracey trimmer are out of date, but the vast majority of the how to information is timeless. I highly recommend it to you.

https://www.amazon.com/Handloading-Competition-Making-Target-Bigger/dp/096269259X

edit: just saw the question about RCBS lube. I haven't used it about many years, but it worked fine. Just make sure to use a very thin layer and keep it off of the shoulders. If they dent from lube, don't worry about it, no big deal. Back in the day, they included a handle with a small nylon brush to lube the inside of the necks.

Back in the day, STP Oil Treatment cut with paint thinner worked and was cheap too.

Have to say, Hornady One Shot sure is quick and cleans up much easier. Put 50 cases upright in a tray, spray at a 45 degree angle to make sure the inside of the necks are lubed in addition to the body, rotate 180 degrees, repeat and go size. Best to start off a bit on the heavy side and have a stuck case remover handy when starting off with the One Shot.

Imperial Sizing Wax is the one other lube I use now, especially when setting up a new die as it does not dry like the One Shot lube.

Nonetheless, the RCBS lube works fine.

Re: Cleaning between firings [Re: patriot07] #7043398 01/18/18 08:17 PM
Joined: Mar 2012
Posts: 3,809
C
Cleric Offline
Extreme Tracker
Offline
Extreme Tracker
C
Joined: Mar 2012
Posts: 3,809
I still use stainless steel blush

deprime then clean

Re: Cleaning between firings [Re: patriot07] #7043439 01/18/18 08:52 PM
Joined: Feb 2011
Posts: 3,018
B
Bar-D Online Mad
Veteran Tracker
Online Mad
Veteran Tracker
B
Joined: Feb 2011
Posts: 3,018
Originally Posted By: patriot07
Originally Posted By: jeffbird
Tumbler with plain corn cob, nothing added, before sizing to protect the sizing die and again after sizing to remove all sizing lube. I turn it on before going to sleep and turn it off in the morning. New brass is cleaned only after going through the sizer to straighten dented necks, and does not take long.

Hornady One Shot is used for lube, except for setting up a new die. Then Imperial Sizing lube is used to avoid sticking a case.

Thanks. Is there anything inherently wrong with RCBS lube? Lots of folks seem to be using the Hornady.


IMO, no there is nothing wrong with it. I have used it for over 40 years. Just be sure and not lube your cases too heavily, especially bottleneck rifle cases, it will cause shoulder dents when you run it through the sizing die.

Last edited by bar-d; 01/18/18 08:52 PM.

People sleep peaceably in their beds at night only because rough men stand ready to do violence on their behalf
Re: Cleaning between firings [Re: Cleric] #7043631 01/18/18 11:32 PM
Joined: Dec 2008
Posts: 41,083
J.G. Online Content
THF Celebrity
Online Content
THF Celebrity
Joined: Dec 2008
Posts: 41,083
Originally Posted By: Cleric
I still use stainless steel blush

deprime then clean


What I do on range pick-up that has lived on the ground from 2 hours to 2 months. But I don't after that initial cycle. Judd convinced me carbon in the neck is a good thing.


[Linked Image]
800 Yard Steel Range
Precision Rifle Instruction
Memberships and Classes Available
Re: Cleaning between firings [Re: patriot07] #7043871 01/19/18 02:03 AM
Joined: Nov 2011
Posts: 4,539
P
patriot07 Online Content OP
Extreme Tracker
OP Online Content
Extreme Tracker
P
Joined: Nov 2011
Posts: 4,539
Thanks everyone for the input. I'll see if I can make some progress this weekend.

Previous Thread
Index
Next Thread

© 2004-2024 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3