Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
Garrett Kreft, AKC Labrador Puppies, drphilwv, WWiggins, st3w4rt
63095 Registered Users
Top Posters
dogcatcher 84422
stxranchman 52093
RWH24 44568
rifleman 44320
BOBO the Clown 43049
bill oxner 42833
BMD 40628
Big Orn 37484
txshntr 35005
SnakeWrangler 31734
facebook
Forum Stats
63095 Members
46 Forums
443778 Topics
6113690 Posts

Max Online: 16728 @ 03/25/12 08:51 AM
Topic Options
#6994038 - 12/12/17 07:27 PM AR500 Plate - 1/2"
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
As before...1/2" AR500 - NOT 3/8"!! Cut mostly larger pieces this time as requested

8" - 25.00 - 11 left
12" - 40.00 - 12 left
14" - 55.00 - 1 left

8 and 12 inch can fit in USPS Flat Rate boxes..

These will all be square targets with rounded corners and two bolt holes for hanging. As before, I take no responsibility for you shooting at steel. Encourage you to read up on it. Again, this is 1/2" thick!



Edited by jbd76266 (01/01/18 01:17 PM)
Edit Reason: Update quantities

Top
#7007684 - 12/22/17 04:12 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
Plates are all cut ready to go...marked up OP with qtys.

Thanks




Edited by jbd76266 (12/22/17 04:15 PM)

Top
#7009970 - 12/24/17 11:27 AM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
Bump!

Edit to answer question below : These are plasma cut. It is shown to have virtually no effect on the quality of the target. See attached link. Note that the response from user "jimcolt" who is with Hypertherm...the leader in plasma tech. Water cut/laser cut is no better than plasma,

http://www.plasmaspider.com/viewtopic.php?t=12813


Edited by jbd76266 (12/24/17 05:07 PM)

Top
#7010355 - 12/24/17 04:58 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
Chuckw Offline
Bird Dog

Registered: 11/05/14
Posts: 257
Loc: tx panhandle
are these water jet cut?

Top
#7018552 - 12/31/17 03:20 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
TTT

Top
#7036412 - 01/12/18 09:49 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
Bump

Top
#7036450 - 01/12/18 10:23 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
doc606 Online   content
Tracker

Registered: 08/09/06
Posts: 788
Loc: hillsboro,tx
Can you cut the round targets with arm to make dueling tree?

Top
#7037565 - 01/13/18 10:00 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
THETEXAN Offline
Pro Tracker

Registered: 01/06/11
Posts: 1730
Loc: Northlake Tx
Pm sent
_________________________

You Don't Have A PIG Problem If Ya Want to Charge $200.00

Top
#7037791 - 01/14/18 09:15 AM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
Originally Posted By: jbd76266
As before...1/2" AR500 - NOT 3/8"!! Cut mostly larger pieces this time as requested

8" - 25.00 - 10 left
12" - 40.00 - 9 left
14" - 55.00 - 1 left

8 and 12 inch can fit in USPS Medium Flat Rate boxes..13.60

These will all be square targets with rounded corners and two bolt holes for hanging. As before, I take no responsibility for you shooting at steel. Encourage you to read up on it. Again, this is 1/2" thick!



Updated qty's. The plate is all cut, so I can not cut up special sizes at this time. Just the square shapes above available.


Edited by jbd76266 (01/20/18 06:54 PM)

Top
#7046529 - 01/20/18 06:55 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
jbd76266 Online   content


Registered: 04/17/09
Posts: 4549
Loc: Sanger, TX
Bump

Top
#7046539 - 01/20/18 07:05 PM Re: AR500 Plate - 1/2" [Re: jbd76266]
txbobcat Online   content
Veteran Tracker

Registered: 06/18/05
Posts: 2627
Loc: TX
What brand plasma table setup do you run?

Top



© 2004-2016 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide