Forums46
Topics537,815
Posts9,729,459
Members87,042
|
Most Online25,604 Feb 12th, 2024
|
|
|
Bedding question
#6837266
07/28/17 11:53 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
I have a savage 114 classic wood stock with accutriger and detachable magazine. I bought a pillar bedding kit for it and was going to start on it when I took the stock off I found it already had some type of insert in it. Not sure what they are. If they are factory pillars they were incredibly poorly done as they are a 1/16 inch or so recessed into the stock. Here are a few pics, and thoughts appreciated. Thanks, Matt
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6837292
07/29/17 12:12 AM
|
Joined: Aug 2012
Posts: 3,993
ImTheReasonDovesMourn
Snarky Mark
|
Snarky Mark
Joined: Aug 2012
Posts: 3,993 |
Are the inserts aluminum or plastic?
Haha yea I polished that thing for hours.
|
|
|
Re: Bedding question
[Re: redchevy]
#6837299
07/29/17 12:21 AM
|
Joined: May 2017
Posts: 5,192
Smokey Bear
THF Trophy Hunter
|
THF Trophy Hunter
Joined: May 2017
Posts: 5,192 |
My guess is poorly done. Savage touts a lot of their rifles as pillar bedded. I have a non accustock model 16 that is pillar bedded. The stock is pretty flexible but the pillars in it are the only thing that contacts the stock. Action and barrel are floated.
Smokey Bear---Lone Star State.
|
|
|
Re: Bedding question
[Re: redchevy]
#6837320
07/29/17 12:35 AM
|
Joined: Dec 2008
Posts: 41,164
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,164 |
thoughts appreciated. Thanks, Matt See if you can get those out, and install the kit you bought. That's my thought.
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Re: Bedding question
[Re: J.G.]
#6837346
07/29/17 01:00 AM
|
Joined: May 2017
Posts: 5,192
Smokey Bear
THF Trophy Hunter
|
THF Trophy Hunter
Joined: May 2017
Posts: 5,192 |
thoughts appreciated. Thanks, Matt See if you can get those out, and install the kit you bought. That's my thought. That would be my approach as well
Smokey Bear---Lone Star State.
|
|
|
Re: Bedding question
[Re: redchevy]
#6837350
07/29/17 01:03 AM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
Will try to get them out tomorrow. They appear to be glued in so we will see. Thanks
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6837589
07/29/17 04:32 AM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
Looked a little closer when I got home they are aluminum. I'm relatively new to working on guns past cleaning them but that is one hell of a sorry excuse for a factory pillar bedding. The action screws were also incredibly loose!
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6837593
07/29/17 04:37 AM
|
Joined: Sep 2006
Posts: 32,488
kmon11
junior
|
junior
Joined: Sep 2006
Posts: 32,488 |
try to get those pit and if that doesn't work glass bed it. Pillar and glass bed go hand and hand anyway
lf the saying "Liar, Liar your pants on fire" were true Mainstream news might be fun to watch
|
|
|
Re: Bedding question
[Re: redchevy]
#6838002
07/29/17 08:28 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
I got the factory pillars out pretty pitiful. Drilled new holes wished I had a drill press but it will work. Need to trim down the pillars for length and I'll be ready to mix up my epoxy.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6838443
07/30/17 02:53 AM
|
Joined: Nov 2010
Posts: 507
scdogman
Tracker
|
Tracker
Joined: Nov 2010
Posts: 507 |
How does the gun shoot now?
|
|
|
Re: Bedding question
[Re: redchevy]
#6839932
07/31/17 04:47 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
I have not finished the pillars yet, I ran out of time so it is all still sitting on the work bench. I measured how long I need to cut my pillars but still need to cut them.
The gun has always shot "ok" but I expected more out of it, especially because the reputation that savages aren't pretty or expensive but they "shoot". I think its a good looking gun, but every other bolt gun I own including 4 factory stock rem 700's and a wby vanguard will out shoot it. Hope to get it stuck back together this week some time and who knows when I will get a chance to shoot it.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6839964
07/31/17 05:04 PM
|
Joined: Sep 2009
Posts: 4,755
ccoker
Extreme Tracker
|
Extreme Tracker
Joined: Sep 2009
Posts: 4,755 |
If you bed the action don't bed the rear tang area.. I have read that Savages need to bedded a bit different than other actions.
I have a barreled action with a custom barrel on it I need to bed in a McMillan and I haven't done it yet as I have read different takes on bedding them. But one thing that has been consistent is not bedding the rear tange area with the safety, it needs some roon for the safety to work.
|
|
|
Re: Bedding question
[Re: redchevy]
#6840005
07/31/17 05:27 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
Yes, I have read the same thing about the rear tang, it will be floated.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6958606
11/13/17 08:05 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
Well... a little blast from the past. Last week I was able to finally get the pillars cut down to the right length. I flubbed one and cut it too short by a smidge but epoxyy'ed a washer on the bottom of it and trimmed down with an angle grinder and its as good as new. Got it all glued torqued down and it all came back apart like it should... whew Took it to the range and it noticeably shot better. It apparently likes 40 grains of IMR 4350 and a 100 grain bullet. I only shot at 100 yards but 100 grain prohunters, 100 grain Partitions, and 100 grain hornady's all grouped sub inch for 3 shots. Mainly wanted to see if there was any improvement, and I definitely think there was, I would say my average group size was about 50% smaller after pillar bedding. In the future if I was going to do it again I think I would find someone I know with a drill press, drilling the holes straight was a little trouble, and I had issues with the stock chipping some on both sides. With a savage the area you are drilling through is very thin to begin with, not much room for error! I may do one of my remingtons or my wby vanguard next, I think they will be more friendly than the savage was by a long shot.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6958777
11/13/17 10:17 PM
|
Joined: Jan 2012
Posts: 9,273
blackcoal
THF Trophy Hunter
|
THF Trophy Hunter
Joined: Jan 2012
Posts: 9,273 |
Usually a tad easier the second, third time plus you feel more confident in what you are doing. happy it worked out and you feel it was worth the effort....
The Greatest Enemy of knowledge is not ignorance, it is the illusion of knowledge.--Stephen Hawking
|
|
|
Re: Bedding question
[Re: redchevy]
#6958813
11/13/17 10:43 PM
|
Joined: Dec 2011
Posts: 3,568
garyrapp55
Extreme Tracker
|
Extreme Tracker
Joined: Dec 2011
Posts: 3,568 |
a little blast from the past thanks for the follow up, to me, it's nice to see results good or bad
|
|
|
Re: Bedding question
[Re: redchevy]
#6958815
11/13/17 10:46 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
Total cost, I spend $20 on the bedding kit and I had to buy a drill bit and a file. I used some axle grease on spots to keep from making the barreled action a permanent fixture in the stock. All in was les than $40.
Before bedding my Best groups were around an inch with the norm being 1.25-1.5. I didn't do any extensive shooting yet but it is for sure better and brought a smile to my face. I didn't wait to get my target but sure wish I had it. No doubt a few more trips to the range will have my shooting form a little better as well, I have not put in to much practice in the past few years.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6958892
11/13/17 11:28 PM
|
Joined: Sep 2006
Posts: 32,488
kmon11
junior
|
junior
Joined: Sep 2006
Posts: 32,488 |
Like said above it does get easier the more you do it, but the last one done around this house I paid to have it done. Gun was already getting a new barrel and some stock work so it made sense to me.
lf the saying "Liar, Liar your pants on fire" were true Mainstream news might be fun to watch
|
|
|
Re: Bedding question
[Re: redchevy]
#6959588
11/14/17 01:40 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
I like to do whatever I can myself. It did take me a while to complete, but I enjoyed it. My dad says the tinkering gene skips a generation and that Papa definitely passed his on to me lol.
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6959741
11/14/17 03:23 PM
|
Joined: Sep 2009
Posts: 4,755
ccoker
Extreme Tracker
|
Extreme Tracker
Joined: Sep 2009
Posts: 4,755 |
yeah, it can be fun to do things yourself, a sense of completion. Like hunting with a rifle and loads you worked on, processing yourself and then cooking it..
|
|
|
Re: Bedding question
[Re: ccoker]
#6959877
11/14/17 04:58 PM
|
Joined: Oct 2004
Posts: 39,536
redchevy
OP
THF Celebrity
|
OP
THF Celebrity
Joined: Oct 2004
Posts: 39,536 |
yeah, it can be fun to do things yourself, a sense of completion. Like hunting with a rifle and loads you worked on, processing yourself and then cooking it..
It's hell eatin em live
|
|
|
Re: Bedding question
[Re: redchevy]
#6959905
11/14/17 05:14 PM
|
Joined: Sep 2006
Posts: 32,488
kmon11
junior
|
junior
Joined: Sep 2006
Posts: 32,488 |
yeah, it can be fun to do things yourself, a sense of completion. Like hunting with a rifle and loads you worked on, processing yourself and then cooking it.. Agree, that one I had the smith do was going to require more build up than I had done and since he was channeling out the barrel channel some for a new barrel contour it made sense for him to bed the action to get it all correct for time of pickup. Made his job and mine easier. Some things I will gladly do others I think I an better off letting a pro do the work.
lf the saying "Liar, Liar your pants on fire" were true Mainstream news might be fun to watch
|
|
|
Re: Bedding question
[Re: redchevy]
#6960040
11/14/17 06:49 PM
|
Joined: Dec 2008
Posts: 41,164
J.G.
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 41,164 |
Nice when a plan comes together. Congrats!
800 Yard Steel Range Precision Rifle Instruction Memberships and Classes Available
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, TreeBass, txcornhusker
|