texashuntingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
nmmuledeerhunter, Dzia-Dzia, TraeMartin, Beatixre, MooseSteed
71989 Registered Users
Top Posters(All Time)
dogcatcher 110,788
bill oxner 91,416
SnakeWrangler 65,416
stxranchman 60,296
Gravytrain 46,950
RKHarm24 44,585
rifleman 44,461
Stub 43,769
Forum Statistics
Forums46
Topics537,029
Posts9,719,585
Members86,989
Most Online25,604
Feb 12th, 2024
Print Thread
Scope mounting rings and base recomm? #6496359 10/15/16 03:13 PM
Joined: Sep 2004
Posts: 482
C
coachmas Offline OP
Bird Dog
OP Offline
Bird Dog
C
Joined: Sep 2004
Posts: 482
Recently picked up one of the vortex viper scopes on sale at Cabelas. I plan on putting it on a Remington model 700 in .270 I got this summer. Needing suggestions for mounting the viper HS on my gun. The gun has a one piece Leupold base already. What do you suggest? Start over with new base and rings, or buy new set of 30mm rings to go with Leupold base already there. What height rings? I'm new to all this. Only have 2 other scopes rifles and they were fully setup when purchased. Thanks in advance for your help. Coach

Re: Scope mounting rings and base recomm? [Re: coachmas] #6496519 10/15/16 06:01 PM
Joined: Jan 2011
Posts: 2,394
B
booradley Offline
Veteran Tracker
Offline
Veteran Tracker
B
Joined: Jan 2011
Posts: 2,394
Nothing wrong with a one piece Leupold base IMO. I've started using picatinny bases though so I'll never have to worry about the scope being too short to mount. It happens more often than you might think.


Don’t roll those bloodshot eyes at me.
Re: Scope mounting rings and base recomm? [Re: coachmas] #6496578 10/15/16 07:17 PM
Joined: Apr 2011
Posts: 3,594
S
Skylar Mac Offline
Extreme Tracker
Offline
Extreme Tracker
S
Joined: Apr 2011
Posts: 3,594
Coach,

Is this going to be a hunting rig?
If so, while Brad's choice is notable, I would also suggest looking into Talley. Their Lightweight aluminum rings are a solid solution. Another one I would look into is DNZ. Similar by design, although they have a cross member connecting the action and bridge together.

Without seeing the rifle and taking measurements, it is going to be hard to recommend a ring height sigh unseen. The Viper is available in several different sizes. Also, there are over 70 variants of the stock Remington 700 with seven different barrel contours.

Although, what you can do is measure the thickness of your bases. Then add the height of the rings. Note, you want to measure to the center line of the ring. Not where the scope rests.
Measuring the thickness of the bases plus the height of the rings and set that number to the side for a moment.

Then, measure the overall outside diameter of the objective. Not the lens, but the outside of the housing. If you plan to use covers, but them on and include that in your measurement. Then, take that number and divide it in half. Say it is 60mm, divided in half would be 30mm, right?


Now, take the sum of your rings and bases measurement, subtract it from the OD measurement.
If the number comes out positive, then you have adequate linear clearance. If negative, then it will be too low and scope will be resting on the barrel.

Oh, the other thing I just thought about, you may want to err on the side of going slightly higher due to the bolt interface. You wouldn't want to rotate the bolt to unchamber or chamber a round it doesn't hit the ocular housing.

Re: Scope mounting rings and base recomm? [Re: coachmas] #6497168 10/16/16 02:18 AM
Joined: Sep 2004
Posts: 482
C
coachmas Offline OP
Bird Dog
OP Offline
Bird Dog
C
Joined: Sep 2004
Posts: 482
Yes it is a hunting rig. Thank you for the info. Coach

Previous Thread
Index
Next Thread

© 2004-2024 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3