Forums46
Topics537,797
Posts9,729,257
Members87,042
|
Most Online25,604 Feb 12th, 2024
|
|
|
6.5 Creedmore with 30 inch tube a mistake?
#6300829
05/17/16 12:41 AM
|
Joined: May 2014
Posts: 1,100
TackDriver
OP
Pro Tracker
|
OP
Pro Tracker
Joined: May 2014
Posts: 1,100 |
After reading many articles and hearing many opinions that a 30 inch pipe in a 6.5 Creedmore is not a great idea according to optimal barrel time. Most used 24 to 26 inch barrels. If that is the case with H4350 not burning the powder all the way down to the muzzle before the bullet goes into flight, would a slower powder work? Has anyone used a H4831SC or a powder which is slower than H4350 and may have better optimal burn time??
|
|
|
Re: 6.5 Creedmore with 30 inch tube a mistake?
[Re: TackDriver]
#6300961
05/17/16 02:23 AM
|
Joined: Nov 2007
Posts: 9,517
RiverRider
THF Trophy Hunter
|
THF Trophy Hunter
Joined: Nov 2007
Posts: 9,517 |
OBT doesn't have anything to do with burning powder all the way to exit from the muzzle. What a slower burning powder does for you is allow you to increase the charge weight, which in turn generates a greater volume of gas, which in turn takes advantage of barrel length. But you are not going to get a powder to burn all the way to exit from the muzzle. All the powder that is going to burn will have done so by the time the bullet travels about four or five inches in a cartridge like the 6.5 Creed. At that point in time, pressure is relieved via bullet displacement to the point that the pressure falls and the burn will essentially cease. Remember---that's how a progressive burning propellant works.
OBT has to do with physical dimensions of the bore being slightly distorted by a shock wave that travels from one end of the barrel to the other, reflecting back and forth. You want the bullet to exit at a time when the bore dimension is changing least. QuickLOAD can supposedly help figure out how to make bullet exit take place at just the right instant.
"Arguing with you always makes me thirsty." -Augustus McRae
|
|
|
Re: 6.5 Creedmore with 30 inch tube a mistake?
[Re: TackDriver]
#6301313
05/17/16 02:32 PM
|
Joined: Sep 2009
Posts: 18,942
ChadTRG42
THF Celebrity
|
THF Celebrity
Joined: Sep 2009
Posts: 18,942 |
Stan, I think your fine with a 30". For giggles, I ran some numbers for you. The 30" barrel will yield higher speeds. But there are diminishing returns. The velocity begins to gain less speed around the 20"-22" length. But you still get a gain with each inch of barrel, that's common sense. The slower powders will help with that.
2.820" COAL 24" barrel with H4350 and 140 grain A-max ran with QuickLoad everything at 61,800K psi 2775 fps with 42.5 grains H4350 30" barrel- 2899 fps same powder charge
H4831 with 45.6 grains at 61,900 psi 24" - 2809 fps 30"- 2940 fps
H4831 shows a calculated 40 fps gain over H4350. It's worth a try to see what the rifle likes and see actual fps results. But still try the tired and true H4350. 40 fps, IMO, is close enough to a wash between the 2 powders. Now, if you went with a powder like R17, you would see more of a gain, but the temp sensitivity could be a big issue.
When I first started competing, I ran a 260 Rem with a 28" barrel. I was a velocity whore (at the time). I ran all the numbers with the various powders. My research showed that I could run H1000 around 49-50 grains and get the most speed out of my 260 Rem. The problem was, I couldn't get 49 grains in the case! It was a heavily compressed load, and the powder would push the bullet out after sitting over night. It would change my seating depth of the 140 VLD and would now be well into the lands. I couldn't get enough powder in there and keep the bullet where I wanted, so that plan was shot. I tried H4831 and H4350, and got a little more speed than H4350, but the H4350 shot MUCH better, was less finicky, and had a large sweet spot forward and back of my load, so that's what I ran. Let the rifle tell you what it wants. You will already be running faster than a common 6.5 CM, and will be flatter shooting with less wind drift. So, just run what the rifle likes, and don't worry about the speed.
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, TreeBass, txcornhusker
|