Forums46
Topics537,783
Posts9,729,080
Members87,042
|
Most Online25,604 Feb 12th, 2024
|
|
|
Feeder legs - Fortify
#6293861
05/10/16 07:32 PM
|
Joined: Aug 2010
Posts: 454
Eastxhuntr
OP
Bird Dog
|
OP
Bird Dog
Joined: Aug 2010
Posts: 454 |
I'm sure this has been posted before. Anyone coming up with better ideas to doctor your feeder legs in protection from hogs knocking them over - varmints?
Was thinking of introducing the barbed wire around the legs trick. Anyone else do that? Thoughts?
Thanks
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6293916
05/10/16 08:01 PM
|
Joined: Nov 2011
Posts: 10,988
Texas buckeye
THF Celebrity
|
THF Celebrity
Joined: Nov 2011
Posts: 10,988 |
drive a t post and wire them to it. That's the best way to keep them from knocking it over. don't know that barbed wire would keep the hogs off the legs as they run under barbed wire al the time, they use it as a back scratcher...
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6293931
05/10/16 08:09 PM
|
Joined: Dec 2008
Posts: 22,630
Cast
THF Celebrity
|
THF Celebrity
Joined: Dec 2008
Posts: 22,630 |
Like this, tee post driven at the opposite angle as the leg, with flat side of post against leg.. I use some SS safety wire to then wrap several wraps around the leg and post, between the teeth on the post. Baling wire will be just fine.
Cast I have a short attention spa
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6294155
05/10/16 10:39 PM
|
Joined: Jun 2015
Posts: 11,534
rickym
THF Celebrity
|
THF Celebrity
Joined: Jun 2015
Posts: 11,534 |
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6294330
05/11/16 12:46 AM
|
Joined: Apr 2011
Posts: 29,034
Western
THF Celebrity
|
THF Celebrity
Joined: Apr 2011
Posts: 29,034 |
Just be extra mindful when filling your feeders, in other words, don't fall on a "T" post...That would really suck....
If at first you dont succeed, then skydiving is not for you..
"Don't trust everything you read on the Internet"- Abraham Lincoln Dennis
|
|
|
Re: Feeder legs - Fortify
[Re: Western]
#6294343
05/11/16 12:53 AM
|
Joined: Jun 2015
Posts: 11,534
rickym
THF Celebrity
|
THF Celebrity
Joined: Jun 2015
Posts: 11,534 |
Just be extra mindful when filling your feeders, in other words, don't fall on a "T" post...That would really suck.... Ah yes, cut a hole in tennis balls and slide over the top of t post, it'll still hurt if you fall but it'll usually keep you from getting a hole or dying
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6294349
05/11/16 12:58 AM
|
Joined: Jul 2013
Posts: 6,061
Wilhunt
THF Trophy Hunter
|
THF Trophy Hunter
Joined: Jul 2013
Posts: 6,061 |
Have one feeder they knocked down four times and had t-posts on each leg each time. In addition to the t-posts I ran t- post across to each leg and tied them all togeather. They have not been able to knock it over since.
|
|
|
Re: Feeder legs - Fortify
[Re: Western]
#6294372
05/11/16 01:09 AM
|
Joined: Feb 2007
Posts: 26,548
JCB
THF Celebrity
|
THF Celebrity
Joined: Feb 2007
Posts: 26,548 |
Just be extra mindful when filling your feeders, in other words, don't fall on a "T" post...That would really suck.... Yup! A forum member was killed a few years ago when he fell onto a T-post. I think his accident was from falling out of a stand onto a T-post that was anchoring the stand but same thing can happen when filling a feeder. I have been using heavy duty electrical conduit for my legs. I leave them 10' for a wider stance. So far I have only had one bent and it was from two bucks fighting. One lease member where I hunt uses the same legs I do and he had a whopper of a hog take his feeder to the ground but that's the first time I have ever seen it happen with the conduit legs and Moultrie bracket system.
|
|
|
Re: Feeder legs - Fortify
[Re: JCB]
#6294576
05/11/16 02:57 AM
|
Joined: Apr 2011
Posts: 29,034
Western
THF Celebrity
|
THF Celebrity
Joined: Apr 2011
Posts: 29,034 |
Just be extra mindful when filling your feeders, in other words, don't fall on a "T" post...That would really suck.... Yup! A forum member was killed a few years ago when he fell onto a T-post. I think his accident was from falling out of a stand onto a T-post that was anchoring the stand but same thing can happen when filling a feeder. I have been using heavy duty electrical conduit for my legs. I leave them 10' for a wider stance. So far I have only had one bent and it was from two bucks fighting. One lease member where I hunt uses the same legs I do and he had a whopper of a hog take his feeder to the ground but that's the first time I have ever seen it happen with the conduit legs and Moultrie bracket system. Have basically the same kind of legs on my last 2 feeders since around 2002, except they are stainless. Don't have hogs here to test it, but had it around horses and cattle and never lost one, came close...No T post driven in... Did have to do that though with goats at the one lease
If at first you dont succeed, then skydiving is not for you..
"Don't trust everything you read on the Internet"- Abraham Lincoln Dennis
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6298310
05/14/16 08:46 AM
|
Joined: Oct 2010
Posts: 482
Deersteaks
Bird Dog
|
Bird Dog
Joined: Oct 2010
Posts: 482 |
I have had luck setting my T-post right next to the feeder legs, running parallel with the legs. This prevents the hogs from pushing on them from any angle without pushing on the T-post. Wiring them together makes knocking it over nearly impossible.
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6303659
05/19/16 01:06 PM
|
Joined: Oct 2009
Posts: 2,316
White Falcon
Veteran Tracker
|
Veteran Tracker
Joined: Oct 2009
Posts: 2,316 |
If you leave a big opening where the leg and post cross hogs will get their heads in that and lift the t-post and leg up. Learned thee hard way years ago.
|
|
|
Re: Feeder legs - Fortify
[Re: White Falcon]
#6303815
05/19/16 02:52 PM
|
Joined: May 2013
Posts: 180
Dead Eye Mike
Woodsman
|
Woodsman
Joined: May 2013
Posts: 180 |
Drive the t post parallel to the legs. It is safer and seems to hold better.
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6306626
05/22/16 12:41 AM
|
Joined: Aug 2015
Posts: 868
Txhillbilly
Tracker
|
Tracker
Joined: Aug 2015
Posts: 868 |
I have two 30 gallon plastic Moultrie feeders that the large boars on my last hunting spot figured out that if they leaned on the legs that they would bend and the feeder's would fall over. This was with the thin tubing Moultrie feeder legs. I bought some 11ga square tubing and welded an 8"x8" 1/2" steel plate and angle iron together for the feeder leg feet. Then drilled 3/4" holes in each corner of the feet bases. I cut 5/8" rebar into 3 ft pcs,and drive then into the ground with a sledgehammer. The ground where I hunt is solid rock about 4-6 inches down,and it takes a lot of beating to get the rebar into it,but I've never lost another feeder from hogs/horses/or bulls.
|
|
|
Re: Feeder legs - Fortify
[Re: Txhillbilly]
#6306695
05/22/16 01:49 AM
|
Joined: Sep 2012
Posts: 949
MoTex
Tracker
|
Tracker
Joined: Sep 2012
Posts: 949 |
I purchased a thinner 3-3.5 ft post at Home Depot. They bend enough that you can drive them parrelel to legs and then zip tie them to the leg. They lay against legs, and hogs can't knock them over and a lot safer ( not exposed so you won't fall on them)
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6307610
05/23/16 01:35 AM
|
Joined: Sep 2009
Posts: 3,060
notamtchance
Veteran Tracker
|
Veteran Tracker
Joined: Sep 2009
Posts: 3,060 |
If y'all look close at the feeder it is a crank style. So the owner does not have to climb up a ladder to fill it making it safe from falling unto T-post. I know I love mine. I don't have to worry about that sudden stop.
Last edited by notamtchance; 05/23/16 01:35 AM.
If I'm not hunting something I must be dead.
|
|
|
Re: Feeder legs - Fortify
[Re: Eastxhuntr]
#6307673
05/23/16 02:24 AM
|
Joined: Aug 2015
Posts: 868
Txhillbilly
Tracker
|
Tracker
Joined: Aug 2015
Posts: 868 |
I just back my truck up to the feeder and transfer the feed from 55 gallon drums to the feeders. It would be pretty hard for me to fall out of the bed of my truck!
|
|
|
Moderated by bigbob_ftw, CCBIRDDOGMAN, Chickenman, Derek, DeRico, Duck_Hunter, hetman, jeh7mmmag, JustWingem, kmon11, kry226, kwrhuntinglab, Payne, pertnear, rifleman, sig226fan (Rguns.com), Superduty, TreeBass, txcornhusker
|