Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
MidCoastHunter, Sternum, Eastexsons, agata28, ghigab
61143 Registered Users
Top Posters
dogcatcher 79448
stxranchman 52092
RWH24 44568
rifleman 43947
BOBO the Clown 41412
BMD 40579
Big Orn 37484
bill oxner 34647
txshntr 34088
sig226fan (Rguns.com) 30961
facebook
Forum Stats
61143 Members
46 Forums
416700 Topics
5758530 Posts

Max Online: 16728 @ 03/25/12 08:51 AM
Topic Options
#5725176 - 05/01/15 11:41 AM DFW J Frame trigger and spring job?
JAK80 Online   content
Tracker

Registered: 12/23/10
Posts: 744
Loc: N DFW
Looking for a good professional gunsmith to do a trigger job and spring replacement on a carry j frame.

Anyone have recommendations?
_________________________
Bad decisions make good stories

Top
#5725672 - 05/01/15 06:33 PM Re: DFW J Frame trigger and spring job? [Re: JAK80]
Tactical Cowboy Online   content
Veteran Tracker

Registered: 08/23/11
Posts: 3031
Loc: Abilene
Buy a spring kit and do it yourself. I'm sure there are plenty of YouTube videos on it.
_________________________
The secret to a long life is to try not to shorten it

Powder coated cast bullets available. https://www.facebook.com/lazyhbullets/

Top
#5726725 - 05/02/15 09:20 PM Re: DFW J Frame trigger and spring job? [Re: JAK80]
JAK80 Online   content
Tracker

Registered: 12/23/10
Posts: 744
Loc: N DFW
As the post states I want an actual trigger job not just a spring replacement.

Yes, I can just do the springs to lighten the pull but it won't smooth the pull out.

TTT
_________________________
Bad decisions make good stories

Top
#5726727 - 05/02/15 09:24 PM Re: DFW J Frame trigger and spring job? [Re: JAK80]
boonee Offline
Veteran Tracker

Registered: 01/09/11
Posts: 2109
Loc: Mesquite
Talk to Lee at Bakes Smoking guns in Terrell.
_________________________
Avenger Firearms 214-577-5818
avengerfirearms@gmail.com

Lifetime NRA member

Top
#5726756 - 05/02/15 09:52 PM Re: DFW J Frame trigger and spring job? [Re: JAK80]
WileyCoyote Online   content
Extreme Tracker

Registered: 09/01/04
Posts: 4712
Loc: The Dogwood Capital of Texas
Can't advise anyone who to use in Dallas anymore, but the guy that did my pin barrel M60 Smith back when it was new'ish put about 6-7 hours of stone work in it, and trimmed the spring about 2-2 1/2 curls as I recall. It's never had a misfire. It has about a 19-20oz SA letoff and a little over 2 lbs DA letoff, with a nice "hesitation" position in DA I can feel and hold at before the super crisp letoff. The trigger is smooth enough that I can shoot DA rapid fire and the barrel never wobbles as it cycles the cylinder.

The work was done in Gilmer, by the store mgr of Dale's Gunshop that was owned by the Head Deputy and later Sheriff of Upshur County. I cannot imagine what this same kind of work would cost today, on an hourly gunsmith rate. This'un 'ill go in the box with me when it's my time.
Ron
_________________________
Remember Aesops Fables outcome of the "Scorpion & and the Frog's" crossing the river when they get to other side

a LOT of Money doan't buy you ANY Class..old South Oak Cliff mantra

Those who fail to learn from History are doomed to repeat it...Santayana

Top



© 2004-2016 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide